Curitiba · Brazil
Elastobras

Extrusion · Profiles, cords and tubing

Custom silicone and rubber extrusions: profiles, cords and tubing

Solid and sponge profiles, cords and tubing in silicone, EPDM and NBR, extruded to your drawing on three lines with hot-air vulcanisation and cut to length with 100% inline inspection. The compound is mixed in our own plant, so the profile and the material are developed together.

We supply companies only, in production quantities. Minimum length is set by the profile, typically from 200 m. We do not sell by the metre to end consumers.

Extrusion lines
3
Cut parts per month
Millions
Cut parts inspected
100%
Hardness
25–90 Sh A
Minimum length
200 m
Extruded silicone profiles and tubes in clear, black, white and grey, cut to length, next to a calliper
Illustration of the product line.

Problems we solve

Do you recognise any of these? Most are solved with the right material, section or tooling. Tell us which one is yours and send the drawing, a sample or the part that failed.

The door or lid takes too much force to close

A sponge profile compresses with little force and fills the gap. We adjust density and section to the closing force your design allows.

The gasket flattens and never comes back

Permanent set comes from a compound that does not suit the temperature or the time under compression. We choose compound and hardness for your duty, and change the rubber or move to silicone when needed.

My supplier does not make my section

We extrude the section from your drawing. An extrusion die usually costs far less than an injection mold, so a custom profile is often within reach.

I need silicone tubing in an exact size

Inside diameter and wall to your drawing, cut to length or continuous, from 200 m.

The seal yellows, cracks or hardens outdoors

For sun, ozone and weather we use silicone or EPDM. The compound is mixed here, so we tune it to your application.

A profile supplier has left me stranded

Continuous series for years, including for export, on three extrusion lines. We schedule supply with you.

What we extrude

Solid profiles

Sealing, guide and protection profiles in solid silicone, EPDM or NBR, produced to the section on your drawing.

Sponge profiles and cords

Sponge silicone profiles, EPDM sponge seal profiles and sponge cords for seals that must close with low force — doors, covers, housings and enclosures.

Tubing and hoses

Silicone and rubber tubing for fluid and air transfer and for protective sleeves, in the bore and wall on your drawing.

Cut-to-length parts

Profiles and tubes cut to length on automated equipment, with every cut part passing 100% inline inspection before packing.

What keeps an extruded seal sealing for years

Compression set

A seal that takes a permanent set stops pushing back against the door, cover or housing it closes, and starts to leak long before it looks worn. Compression set is decided by the compound and by its cure, which is why we formulate, extrude and vulcanise in the same plant.

Solid or sponge

A sponge section closes with a fraction of the force a solid section needs and fills uneven gaps, so it is the usual choice for doors, covers and enclosures with light clamping. A solid section holds its shape, resists abrasion and carries load. The choice is made against the closing force available in your design, not against a catalogue.

Dimensional consistency

How much a section swells as it leaves the die follows the viscosity of the compound. A profile that drifts in size from batch to batch usually has a compound problem, not a die problem. We check every compound batch on the rheometer and for hardness before it reaches the extruder, measure the diameter continuously while the line runs, and inspect every cut part inline.

Service conditions

Silicone for wide temperature ranges and clean environments, EPDM for weather, ozone, UV, hot water and steam, NBR where oil and fuel are present. Temperature, media and outdoor exposure decide the family before the section is drawn.

Cross-sections of extruded rubber and silicone profiles: solid D profile, sponge D profile, P profile, sponge cord and tube
Typical sections, schematic. A — solid D profile. B — sponge D profile. C — P profile with hollow bulb. D — sponge cord. E — tube. Any section is produced to your drawing.
Solid and sponge seal sections compressed by the same closing force
Same closing force F, schematic. 1 — a solid section barely compresses. 2 — a sponge section closes with low force and fills the gap. Dashed line: section before closing.

What we can develop

Any extruded section in silicone or rubber that fits our lines. Send a drawing, a sample, or a short length of the profile you use today: we have the die made for your section, develop the compound and supply a sample length for approval before series production.

Our extrusion lines already run continuous series for export to mining equipment manufacturers, and seals for outdoor housings that have to stay closed for years against water, dust and temperature cycling. Where an application requires food-contact compliance, the compound is qualified by an accredited laboratory as part of the development.

More on the plant in Capabilities and on batch control in Quality.

Materials and production

Sponge and solid sections can be produced in the same family of compound. Colour to requirement, including light silicone.

Materials

Compounded in-house for the application
MaterialFormChosen for
Silicone (VMQ)Solid and spongeWide temperature range, low compression set, clean environments, light colours
EPDMSolid and spongeWeather, ozone, UV, hot water and steam — outdoor housings and enclosures
NBRSolidOils, fuels and hydrocarbons

Production

How extruded parts are made and checked
ItemSpecificationNote
Extrusion lines3Hot-air tunnel vulcanisation
Hardness25–90 Shore ASet by the compound for each application
TolerancesTo customer drawingTightest on functional dimensions
Dimensional controlDiameter measured continuously during extrusionCut parts: 100% automated inline inspection
Supply formContinuous lengths or cut to lengthCutting on automated equipment
Compound controlRheometer curve and hardness on every batchApproved formulation frozen
Minimum quantitySet by the profile, typically from 200 mEach new section needs its own die

Request a quotation

To quote an extruded profile we need:

  • your company and country;
  • a drawing of the section, a sample, or a photo with dimensions;
  • material, hardness and the working environment — temperature, oils, outdoor exposure;
  • supply form (continuous length or cut to length) and the quantity in metres per order and per year.

Request a quotation →

Email an extrusion enquiry →

We supply companies only. Minimum length is set by the profile, typically from 200 m. Enquiries go directly to one of the partners — see Company.