Curitiba · Brazil
Elastobras

Enclosures · Seals, gaskets and grommets

Seals and gaskets for enclosures, closures and outdoor cabinets

Injection-molded and extruded gaskets, grommets and cable-entry seals for fibre optic splice closures, FTTx terminal boxes, EV charger cabinets and other outdoor housings. Silicone and EPDM, compounded in-house and produced to your drawing.

We supply companies only, in production quantities. Each new seal is made in its own tool, and the minimum quantity is agreed per part.

Processes
Injection · extrusion
Materials
Silicone · EPDM
Hardness
25–90 Sh A
Compound
In-house
Certification
ISO 9001
Rubber door gasket inside a metal enclosure and a cable-entry grommet with a cable passing through
Illustration of the product line.

Problems we solve

Do you recognise any of these? Most are solved with the right material, section or tooling. Tell us which one is yours and send the drawing, a sample or the part that failed.

Water or dust gets into the enclosure

The gasket sits in the lid channel and is sized for the compression and the protection rating you need. Silicone or EPDM for outdoor and buried installations.

The cable goes in and the seal fails

Grommets and cable-entry seals with lips that close around the cable, molded for the cable diameter and the wall thickness.

The gasket pops out of the channel or does not close at the corners

We review the channel and the gasket together before any tooling is made, so the geometry works the first time.

The seal hardens or cracks in sun, ozone or cold

We pick the elastomer for the temperature range and exposure of the installation, and mix the compound here.

I want to validate before paying for a full mold

We look for the simplest tooling that proves the design, then scale up once it works.

What we make for enclosures

Fibre optic closures and FTTx boxes

Housing gaskets, cable-entry grommets and port seals for splice closures and terminal boxes — including silicone seals for optical closures designed to be buried underground.

EV charger cabinets

Door and cover gaskets and cable-entry seals for charger housings installed outdoors, where the seal sees sun, rain, washing and temperature cycling every day.

Cable entry

Grommets and multi-hole entry seals that close around the cable range on your drawing and keep sealing after the cable has been pushed through.

The IP rating belongs to the enclosure. The seal decides whether it keeps it.

IP67 and IP68

An IP rating is earned by the complete enclosure, tested as an assembly. We supply seals for enclosures rated IP67/IP68; the rating test is carried out on the customer's assembly. What the seal decides is whether the enclosure still meets that rating after years in the field.

Recovery over years

A lid or door gasket that takes a permanent set stops pushing back against the housing, and the enclosure starts to breathe water long before anyone opens it. Compression set is a property of the compound and its cure, so it is controlled in the mixing room, not at the press.

Outdoor ageing

Ozone, UV, temperature cycling and standing water age a seal differently from a laboratory test. EPDM is the usual choice for weather and ozone; silicone where the temperature range is wide or the closure is buried. The family is chosen against the installation, not against a datasheet.

Consistency between batches

An enclosure is designed around one gasket height and one hardness. We check every compound batch on the rheometer and for hardness before molding, and once a seal is approved its formulation is frozen: no change without prior written notification.

Cross-section of an enclosure gasket compressed between lid and housing
Enclosure seal, schematic section. 1 — lid. 2 — gasket compressed in the lid channel. 3 — housing. 4 — water and dust outside. 5 — protected interior.
Cross-section of a rubber cable-entry grommet in a panel wall with the cable passing through
Cable entry, schematic section. 1 — panel wall. 2 — grommet, with a flange on each side of the wall. 3 — cable. 4 — sealing lips closing around the cable.

What we can develop

Any seal, gasket or grommet in silicone or rubber that fits our machines — injection molded, extruded, or extruded and cut. We also develop extruded door gaskets and molded seals for outdoor telecom and power cabinets, and door and panel gaskets and cable-entry grommets for server racks and data centre enclosures.

Send a drawing, a sample or the enclosure design: we comment on the seal geometry and material before any tooling is committed, supply samples with a dimensional report, and provide PPAP documentation when your approval process requires it.

Extruded door gaskets: see silicone and rubber extrusions. How a new part is developed: Engineering.

Request a quotation

To quote a seal we need:

  • your company and country;
  • a drawing, a sample, or the enclosure design;
  • the enclosure type, its IP rating and the installation — outdoor, buried, washed;
  • the expected quantity per year.

Request a quotation →

Email an enclosure seal enquiry →

We supply companies only. Minimum quantity is agreed per part. Enquiries go directly to one of the partners — see Company.